Plumbing 101: A Guide to Bathtub Installation

Browse Our Site

Everybody is bound to have their unique perception with regards to Installing A Bathtub.


Tools You Need to Install a New Bathtub
Installing a bath tub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably difficult project. If the old tub is readily accessible, the project can move quickly; if you need to open up a wall surface to get rid of the old bathtub and also position the brand-new tub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will need a helper to vacate the old tub as well as set in the brand-new one. Make certain you have certified on your own for the task and are comfortable trying it. Instead of employing a contractor to take over a halfway-completed project, it is much better to consider using one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This article will certainly assist you mount a brand-new tub in your bathroom if you have actually currently acquired a brand-new bathtub as well as do not require to change the arrangement of your previous water supply pipes.
Your devices and also product checklist need to consist of the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Setup


    First of all, the sustaining frame provided with the bath ought to be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
    Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
    Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be suited its final placement.

    Removing Old Taps


    If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the water. After doing so, turn on the taps to drain pipes any water staying in the system. The process of getting rid of the existing faucets can be rather bothersome due to the restricted access that is often the situation.
    Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will come from the pipes. As soon as the supply pipes have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning throughout this procedure. When the faucets have been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
    Prior to moving on to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Mounting the Bathtub


    Utilizing both wooden boards under its feet, position the bath tub in the required setting. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 small factors.
    The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the tub up until the spirit level reads level.
    To mount faucets, fit all-time low of the outermost versatile tap connector to the suitable supply pipe by making a compression join; then do the very same for the other tap.
    Turn on the supply of water and also inspect all joints and brand-new pipework for leaks and tighten them if needed. Fill the bath tub and likewise check the overflow outlet and the normal electrical outlet for leaks.
    Ultimately, take care of the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bathtub ought to wait up until the bathtub has been made use of at the very least when as this will resolve it right into its final position.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a link to the existing supply pipelines.
    If you require to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next, place the tap in the mounting opening in the bath/basin making certain that the washers remain in location between the tap as well as the sink. Secure the faucet in place with the producer offered backnut. When the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The former type ought to be attached to the faucet finishes first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Tiling Around the Tub


    In the location where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall surface in between the bath and also the tiling, resulting in complications with wetness and also feasible leakages to the ceiling below.
    You can choose from a variety of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to permit the movement experienced when the tub is in use. The sealer can split fairly very early if you do not think about this motion before sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly readily available on the marketplace. It is recommended to fit the floor tiles using water-resistant or waterproof adhesive and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    Do you appreciate reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave feedback down below. We would be interested to know your feelings about this piece. Hoping to see you back again in the near future. Sharing is good. Helping others is fun. We truly appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.


    Click Here!

    Leave a Reply

    Your email address will not be published. Required fields are marked *